Home > Products > Molded Case Circuit Breaker > Thermal Magnetic Molded Case Circuit Breaker > 250A Thermal Magnetic Single Knob Molded Case Circuit Breaker
250A Thermal Magnetic Single Knob Molded Case Circuit Breaker
  • 250A Thermal Magnetic Single Knob Molded Case Circuit Breaker250A Thermal Magnetic Single Knob Molded Case Circuit Breaker
  • 250A Thermal Magnetic Single Knob Molded Case Circuit Breaker250A Thermal Magnetic Single Knob Molded Case Circuit Breaker
  • 250A Thermal Magnetic Single Knob Molded Case Circuit Breaker250A Thermal Magnetic Single Knob Molded Case Circuit Breaker
  • 250A Thermal Magnetic Single Knob Molded Case Circuit Breaker250A Thermal Magnetic Single Knob Molded Case Circuit Breaker
  • 250A Thermal Magnetic Single Knob Molded Case Circuit Breaker250A Thermal Magnetic Single Knob Molded Case Circuit Breaker

250A Thermal Magnetic Single Knob Molded Case Circuit Breaker

Saide® SDM6 250A Thermal Magnetic Single Knob Molded Case Circuit Breaker equips with intelligent controller as well, which not only makes its current adjustable but also grants protection against overload (long delay), short-circuit(short delay), short- circuit(instantaneous) & undervoltage, it'll certainly improve the entire power system's reliability, continuity &security.

Send Inquiry

Product Description

RS485 interface,MODBUS-RTU protocol.With MODBUS modul equipped,customers can choose options as below. Remote signal: Switching ON/OFF, tripping, alarm &malfunotional singal indication.

Remote control: Switching ON/OFF,reset.Remote test: 3-phase cuttent &N-pole current, grounding current.Remote adjustment: accept and execute remote command to debug remote control. Tripping unit menory recording function, last three time, tripping records can be well traced.SDM6 circuit breaker also obtains isolation funcion (Can be used as an alternative load switch).

Saide® SDM6 molded case circuit breakers (MCCBs) protect cables sized for 100A to 1600 A. Their highest breaking capacities allow them to protect also smaller cables, when connected close to a powerful energy source. As one pillar of digitally connected power distributions (EcoStruxure Power), SDM6 breakers take part in energy consumption and asset management optimization. Benefit from 25 years of technological leadership, and rely on proven quality, opted for even in most demanding environments.

SDM6 250A Thermal Magnetic Single Knob Molded Case Circuit Breaker complies to GB/T14048.2, IEC60947-2 standards, with CCC.CE, TSE certificate approved.

Saide® SDM6 Series 250A Thermal Magnetic Single Knob Molded Case Circuit Breaker is the company's comprehensive use of international advanced technology design and development and obtained a number of patents of new products, with small SDM6, modular, high break, double breakpoints, 0 of flying arc, green environmental protection and other characteristics. Suitable for AC 50Hz, 60Hz, rated operating voltage 690V and below, rated current 12.5Ato 1600A distribution network, used to distribute electrical energy and protection lines and power supply equipment from overload, short circuit and undervoltage failure hazards. It can also be used as a non-frequent conversion of the line under normal conditions and in the infrequent start of the motor.


Normal work and installation conditions

1. The altitude of the installation site does not exceed 2000m;

2. The SDM6 thermomagmetic iype with temperature of the surrounding medium is -6 ~ +40 , and the average temperature of 24 h is not more than +35*C. The relative humidity of the air at the installation site does not exceed 50% at a maximum temperature of +40P; at lower temperatures, there may be a higher relative humidity; the average minimum temperature of the wettest month does not exceed +25 °C for the average of the month The maximum relative humidity is not more than 90%, and the condensation on the surface of the product due to temperature changes is considered.

3. SDM6 intellgent type with temperature of the surrounding medium is -40 ~ +80

4. The product is used in non-explosive hazardous media, and the media does not have enough to corrode metals and destroy insulating gases and conductive dust.

5. In places where there is rain protection and no water vapor.

6. The installation category is Class III.

7. The pollution level is level 3.

8. The basic installation of the circuit breaker is vertical (ie vertical) or horizontal (ie horizontal).

9. The incoming line is either the up line or the down line.

10. Circuit breakers can be divided into fixed and plug-in types.



Hot Tags: 250A Thermal Magnetic Single Knob Molded Case Circuit Breaker, Manufacturers, Suppliers, China, Factory, Price

Related Category

Send Inquiry

Please feel free to give your inquiry in the form below. We will reply you in 24 hours.